A standard two-storey detached houses WLAN installation usually only need a wireless router at home has led to a central location in the. The latest trend that is crumbling Schaumuburg Computer Repair addresses the new mega-houses that are all brick and three floors with over 4,000 square meters. The question is: how can I give customers the best coverage for the lowest possible price.
Tutorial Standard: 802.11b is old do not use it. 802.11g operates at areported 54Mbps but the actual throughput is 22 Mbit / s, has a range greater than 802.11a. 802.11a office is usually in areas where there are many wireless access points such as the business already. 802.11a network may also be more, find wireless access points, co, because 802.11a is non-overlapping 802.11g channels is 8, while only 3 802.11n is only a draft at this time do not buy Draft-N products. I recommend purchasing the 802.11g Wireless Access Point with MIMO (Multi-In Multi Out). These access points have two radios that send and receive at the same time allow configured.
Phase One: Coverage Area - Definition of service area for the house is very important because the ceiling domains, customers can cost-neutral. We have many customers who make a lot of work in detached garages and basements, but many people use wireless only in one room. So the general rule is, the areas most need> Network coverage, the higher the price for the customer.
Step Two: Site Survey - Before making an investigation to find out what other wireless networks in the area. This is very important in terms of impact because of the possibility, if you install network wireless 802.11g or 802.11a. And if we do a survey of the site, you'll find many 802.11g wireless networks in different channels, it would be better, perhaps , installation of a wireless 802.11b network, which runs onanother frequency. Knowing what other networks of channels is very important to run, because each of wireless access points must be run on another channel. 802.11g have only three non-overlapping channels 1,6 and 11, while 802.11a has eight non-overlapping channels. The general rule to follow is that 802.11g is more subject to interference, but more extensive than 802.11a.
Phase Three: Distibution System - Now you must decide,how do you deploy your wireless network in total. A wireless access point operates a wireless wire, so that you can still find a way to get a network connection for wireless access. There are three options: the installation of cables throughout the house (the worst option), the establishment of Powerline Ethernet or wireless repeater or bridge approach. Roll out the network cable is your last option because it requires drilling and time,corresponding to cost more. Powerline Ethernet is great because you plug the cable into the network. Everything you want to have two plugs in a network device on your wireless router connected to the Internet and then connect the adapter to the house which extends to the wireless access points connected then your final option is to establish a wireless repeater with the original signal through your house.
Step Four: Access Point Placement- Access points should be the first areas in the central part of the house with more wireless access points placed in the hand. Keep your wireless access points away from large metal objects, and if the wireless access point can not be in a central location using directional antennas for outdoor shows the wireless signal, rather than internally.
Step Five: Wireless Access Point Configuration - Survey your site haveshowed that 99% of the defaults you buy a wireless access point to buy better and can connect them all. So this means that the SSID is 6 and the Linksys wireless router / access point channel. Our wireless home network should be even more so for two or three wireless access points will be our first two 11 Configuring wireless access points on channel 1 e. If a third party is required, then you can channel 6, to be sure peopleConnections are not dropped after the wireless clients are configured. Next you want to) the wireless network name (SSID. Choose an obscure names like home, a color or something that can not connect the network with the family. The reason why many people have their SSID as the name of family, there is the same network key or a pet or the child's name. The hacker knows the family, the easier it is to hack the network
Step 6: Security - WantAES encryption with WPA2-treatment for most wireless networks. If your customers go to games encryption over the wireless network you might consider using AES, WEP 128, as in the old wireless access points, the processor high intensity. The myth is that the Wi-Fi encryption packages can crack failed in five minutes, the network is capable of true if you have enough. The whole process is the set of packages and then package crackingThe collection of these packages may take weeks if not months. Then, after the package has collected for the encryption to be broken.
No comments:
Post a Comment